Skip to end of metadata
Go to start of metadata
Table of Contents

Reproduced with permission from http://arika.firstyear.id.au/blog/?p=267


Installation

I tested this on CentOS 5 (As we use RHEL at work), so adjust this for your needs.

If EPEL is not enabled you can enable it with this

EPEL: http://fedoraproject.org/wiki/EPEL

If you wish to only install the one package, you can set the repository to disabled, and install with the following command

yum install --enablerepo=epel mod_auth_cas

Also install the ldap module. It is part of the base repo in RHEL.

yum install mod_authz_ldap

Configuration

Stop your apache server

We need the modules to load in a certain order, so we need to rename our configs.

cd /etc/httpd/conf.d/
mv auth_cas.conf 00_auth_cas.conf
mv authz_ldap.conf 10_authz_ldap.conf
mv ssl.conf 20_ssl.conf

In /etc/httpd/conf.d/00_auth_cas.conf

#
# mod_auth_cas is an Apache 2.0/2.2 compliant module that supports the
# CASv1 and CASv2 protocols
#

LoadModule auth_cas_module modules/mod_auth_cas.so
<IfModule mod_auth_cas.c>
    CASVersion 2
    CASDebug On

    # Validate the authenticity of the login.goshen.edu SSL certificate by
    # checking its chain of authority from the root CA.
    CASCertificatePath /etc/pki/tls/certs/
    CASValidateServer Off
    CASValidateDepth 9

	CASCookiePath /var/lib/cas/

    CASLoginURL https://auth.example.com/cas/login
    CASValidateURL https://auth.example.com/cas/serviceValidate
    CASTimeout 7200
    CASIdleTimeout 7200
  </IfModule>

You need to create the cas tickets directory, else the module will barf.

cd /var/lib
sudo mkdir cas
sudo chown apache:apache cas
sudo chmod 750 cas
sudo semanage fcontext -a -s system_u -t httpd_var_lib_t /var/lib/cas
sudo restorecon -r -v ./

This applies the needed SELinux policy to allow httpd to write to that directory. If you have set SELinux to permissive or disabled, these steps are worth taking incase you enable SELinux again in the future.

Configuration with LDAP authorization

Now we can add our ldap attributes we need. Check that 10_authz_ldap.conf matches the following

#
# mod_authz_ldap can be used to implement access control and
# authenticate users against an LDAP database.
#

LoadModule authz_ldap_module modules/mod_authz_ldap.so

<IfModule mod_authz_ldap.c>

## Some commented code

</IfModule>

Now, in your SSL Directory directive add

<Directory "/var/www/ms1">
    Order allow,deny
    Allow from all
    AuthType CAS
    AuthName "TEST CAS AUTH"
    AuthLDAPURL ldaps://ldap.example.com:636/ou=People,dc=example,dc=com?uid?one?
    require ldap-filter &(uid=username)
  </Directory>

You can start apache again after reading the filter section

Filter

This ldap filter can be anything you desire. It can be a list of UID’s, sets of attributes, etc.

examples:

#Will check for this attribute
&(department=marketing)
#Checks that one has both this class and this department
&(class=compsci1001)(department=marketing)
#Your name is either foo or bar
|(uid=foo)(uid=bar)
#These can be nested as well. This would allow anyone with attr and other attr OR the uid= foo into the site.
|(&((attr=true)(other attr=true)) (uid=foo))

You can read more about filters here

Alternately, one can change the configuration to be like so

    AuthLDAPURL ldaps://ldap.example.com:636/ou=People,dc=example,dc=com?uid?one?(&(attr=foo)(attr=bar))
    Require valid-user

Note the filters are the same, but require the whole filter to be enclosed in a set of ().

  • No labels